Asentria TeleBoss 830 Скачать руководство пользователя страница 95

Страница: 95 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 95

Country

This is a text field. The maximum number of characters is 2. The default is US.

Certificate Installation

Choose File

Use the functions in the Certificate Signing section of the page to generate a key for your third party certificate

authority. Once the CA supplies a certificate key, install the file in the TeleBoss using this button. Once this is

done the Install Externally-signed Certificate button will enable.

Install Externally-signed Certificate

The Install Externally-signed Certificate will be enabled only if user is logged in with MASTER credentials and

a file is loaded with your certificate key from your third party certificate authority using the "Choose File" button

above it. Click this button to install the certificate.

Create Self-signed Certificate

The Create Self-signed Certificate button will be enabled only if the user is logged in with MASTER

credentials. If the button is clicked the information from the General Cerificate section will populate the read

only "Installed Cerificate Information" fields.

Installed Certificate Information

These fields are read only. These read-only items are refreshed in 3 circumstances:

1. Upon initial load.

2. Upon seeing that the user has clicked the "Install Certificate" button.

3. Upon seeing that the user has clicked the "Create Self-signed Certificate" button.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды