Asentria TeleBoss 830 Скачать руководство пользователя страница 26

Страница: 26 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 26

Modem

This field indicates whether the optional internal modem is installed. It will indicate "Yes" if the POTs modem is

installed. It will indicate "None" if no modem or if a Wireless modem card is installed.

Serial Port Section

Port

The currently configured serial port names will display, the default names are I/O1 and I/O2, are displayed for

each of the installed serial ports along with the following information:

Baud/Etc.

Displays the baud, word length, parity, and stop bit settings for each installed serial port.

Recs

Shows the number of carriage return-delimited records stored within the file associated with each serial port.

Bytes

Displays the amount of storage allocated for the above records.

Full

This field is a rough percentage indicator of how much data is stored in a particular file.

Wrap

The indicates the ON/OFF status of whether file wrapping is enabled on a particular port. When ON, a unit

that is 100% full will overwrite the oldest buffered records with new ones. The Wrap Around setting can be

toggled in the

Serial Settings

menu for each port.

Name

Name displays the target name, which is an optional name given to the device connected to the port. This

target name is used in event notifications and can be configured in the

Serial Settings

menu for each port.

EventSensor Status

This status menu is accessed by typing

Sensors

or an ! at the command prompt followed by <Enter>. It

serves as a quick-access menu to all of the EventSensors installed in your TeleBoss, and allows you to read

their current status. Configuration of these sensors must still be done in the Alarm/Event Definitions menu

using the

EventSensor Device Settings

submenu options. Below is a screenshot of a TeleBoss 830

configuration. Your setup will likely differ significantly depending on installed sensors and slot cards.

TeleBoss 830 Current EventSensor Status
Configuration Location Name ID
Alive
A) 2-CC Internal INTERNAL -------- -

Selection?

Configuration

This column is the shorthand name of the sensor. Common examples include CC for contact closures, VS for

voltage sensors, RL for relays, TS for Temperature Sensor and HS for Humidity Sensor. If nothing is

connected to your TeleBoss it will show 2-CC. The two RJ45 IO ports can be configured as contact closures.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды