Asentria TeleBoss 830 Скачать руководство пользователя страница 78

Страница: 78 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 78

Advanced DHCP

Togging the menu opion in the grey bar to Advanced DHCP wil give some advanced settings to define

equipment connected to the Ethernet Expansion ports.

These settings allow an IP address, or an IP address range to be assigned based on a client's MAC address

(partial to full MAC addresses are allowed). For a partial MAC address, an IP address range must be

specified; for a full MAC address, just one IP address is needed. All IP addresses must be on the same

subnet as the Ethernet Expansion IP Address, set in the Basic Settings section.

Class n

The Class drop down box allows for six separate Advanced DCHP IP Address configuration settings classes.

Enable

Click box to enable this DHCP class IP Address settings configuration.

MAC (3 to 6 octets

)

Input the client MAC address. MAC entries must have a minimum of 3 octets, each octet must be two

characters. Octets must be separated by a semi-colon. For example, valid entries could be one of the

following: 00:AA:B0, 10:0a:b0:04:55:60, 10:0a:b0:04:55.

Start IP

Use this field to set a Start IP address for the specified MAC address. If a full MAC address, this is the IP

address that will be assigned to the client with that MAC address, and the end IP address is ignored. If partial

MAC address, this is the starting IP of a range of IPs that will be assigned to clients that match the partial

MAC address.

End IP

This field sets the End IP address for this MAC address range.

Serial Settings

This Menu is sued to configure the two on board serial ports as well as any additional serial ports installed via
4S slot cards.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды