Asentria TeleBoss 830 Скачать руководство пользователя страница 80

Страница: 80 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 80

TeleBoss 830 - Serial 2 Record Stamping
A) Date/Time Stamping [OFF]
B) Site Name Stamping [OFF]

Character Masking

This is an ON/OFF toggle to enable the character mask. The character mask allows you to block most non-

printing ASCII characters. Specifically, the following ASCII character values are blocked: 0, 1, 4-9, 11, 12,

14-31, and 128-255. The default setting is ON.

Data Alarm Enable

This option is an ON/OFF toggle to enable data alarm monitoring for this port. The default setting is OFF.

Store Data To

This selection displays a menu that toggles ON/OFF whether the data received on this port should be stored

to each of the available files or not. The file number that is the same number as the serial port number will be

set to ON by default and the other available options will be set to OFF.

TeleBoss 830 - Store Data To
A) FILE1 [OFF]
B) FILE2 [ON]
C) AUX1 [OFF]
D) AUX2 [OFF]
E) AUX3 [OFF]

Store Alarms During Pass-Through

This is an ON/OFF toggle to determine whether data strings that meet data alarm criteria are stored in the

Events File when a pass-through session is active on this port. The default setting is OFF.

Duplex (I/O 2 only)

Duplex controls the echo settings for the command processor. It toggles between FULL and HALF. Full

duplex causes the unit to echo all characters sent to the connected terminal when in COMMAND mode. Half

duplex turns off character echo. The default setting is FULL.



Note:

If Duplex is set to Half, set

sys.terminal.mode

=OFF. Otherwise, characters will continue to be

echoed to the terminal screen.

Inactivity Timeout (I/O 2 only)

This option sets the number of minutes (0 - 255) to wait before a serial connection with no activity will be

terminated. A setting of 0 means an inactive connection will not be terminated. The default setting is 0.

Port Mode

Port Mode sets the port function.



I/O 2

toggles between COMMAND, DATA, PPP HOST, PPP CLIENT and RESERVED. The default

for I/O2 is COMMAND.

COMMAND allows for serial command processor access.

DATA configures the port as an inbound RS232 data port.

INLINE sets the serial ports to take data from I/O1 and route it out I/O2.



I/O

All other serial I/O have only one option in the TeleBoss which is DATA.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды