manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 25

TeleBoss 830 2.11.370 STD User Manual 

 

Page 25 

 

 

TeleBoss 830 2.11.370 STD  -  Status 
Site Name       : 830-000000000 
Serial Number   : 000000000        Eth 1    : DHCP 
Date            : TUE 09/25/2018   IP Addr  : 192.168.90.76 
Time            : 21:07:02         MAC Addr : 00:10:A3:60:49:91 
Memory          : 63488K           Eth 2    : STATIC 
% Full Alarm    : OFF              IP Addr  : 0.0.0.0 
No-Data Alarm 1 : OFF              MAC Addr : 00:10:A3:60:49:92 
No-Data Alarm 2 : OFF              Modem    : None 
Duplex          : FULL 
------------------------------------------------------------------------- 
Port   Baud/Etc.  Recs     Bytes    Full Wrap Name 
IO1  : 19200,8N1  00002170 00131072   1% OFF  I/O 1 
IO2  : 19200,8N1  00000000 00000000   0% OFF  I/O 2 
 
COMPLETE 
 

 

TeleBoss 830  

This indicates that this product is the T830, followed by 2.11.370 STD, the currently loaded firmware version. 

 

Site Name  

This field displays the identifier assigned to each TeleBoss by the end user in the 

General Settings

 menu. It 

defaults to the units factory assigned Serial Number. 

 

Serial Number  

The Serial Number is the factory-assigned, unique serial number for this TeleBoss. 

 

Date 

and

 Time  

These two fields display the current date and time. The Date and Time can be set in the General Settings 

menu under the 

Date/Time Setup

 option. 

 

Memory  

This field reports the amount of flash memory configured for storage of data. 

 

% Full Alarm / No Data Alarm n  

These options indicates the current ON/OFF status of the % Full Alarm, and No Data Alarms 1 and 2, 

respectively. 

 

Duplex  

This reports the current Duplex echo setting for the command interface. The Duplex echo allow the user to 

see what he or she is typing when using the Command Line Interface. Full duplex causes the TeleBoss to 

echo all characters sent to the remote device. Half duplex turns off character echo. 

 

Eth 1 

and

 Eth 2  

These fields display STATIC, DHCP, or VLAN, depending on which mode each of the two Ethernet interfaces 

is configured for. The settings can be configured in the Network Settings menu under 

Ethernet Settings

.  

 

IP Add 

and

 MAC Add  

Immediately following Eth 1 and Eth 2 are the network IP address assigned to each Ethernet port, and the 

MAC address assigned to each respectively. The MAC addresses can also be found on t

he unit’s serial 

number label. 

 

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды