Asentria TeleBoss 830 Скачать руководство пользователя страница 71

Страница: 71 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 71

Routing Settings as accessed via Web UI

The Routing Settings are reach by navigating to the Networking section of the Setting Menu. Select the

Routing submenu. On the T830 only the Static Routes settings will display.

DSL Settings

The Asentria DSL modem is obsolete, so the DSL settings will have no functional effect.

VPN Settings

The following describes the menu options for configuring VPN Settings. A Virtual Private Network (VPN) is a

network that is tunneled (the virtual part), typically across a public network, and secured (the private part),

typically with IPsec or SSL. There is more information on

SSL

VPNs on the Asentria Product Information

Portal or contact

Asentria Technical Support

. Note the IPsec settings are not functional on this software

version.

The Asentria unit can be configured with up to 2 VPNs. Although the unit supports multiple VPN

configurations, only 1 VPN can be operational at any one time.

TeleBoss 830 - VPN Settings
A) VPN 1 []
B) VPN 2 []

Enter your Selection: a

TeleBoss 830 - VPN 1 Settings
A) Mode [OFF]
B) Start Mode [MANUAL]
C) Description []
D) Remote Host []
E) Public Interface [ANY]
F) IPsec Settings
G) SSL Settings

Mode

Mode toggles between OFF, IPSEC PRIVATE SUBNET, SSL CLIENT, and SSL SERVER to specify the VPN

mode. Default setting is OFF.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды