Asentria TeleBoss 830 Скачать руководство пользователя страница 65

Страница: 65 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 65

Maximum Retries

This field defines the maximum number of times to retry a failed connection for all phone numbers present.

The default setting is 3.

Carrier Detect / Login Sequence Timeout (sec)

These fields set standard login timeouts, from 0 to 65535 seconds. The default setting is 60 seconds for

Carrier Detect, and 30 seconds for Login Sequence.

Dialout Modem Init String

This field sets the modem initialization string (maximum length 48 characters).

IP Address to Suggest

This field sets an IP to try to acquire, if defined. The default setting is 0.0.0.0.

Firewall

This is an ON/OFF toggle to enable or disable the PPP Modem firewall. The default is on.

Maximum Dialout Failures

Each time a call is attempted, the number's failure count is checked before dialing. If the Maximum Dialout

Failure count is reached, then the number will not be dialed until its blackout period expires, or the unit is

restarted. After dialing, if the call is a failure, then the called number's failure count is incremented. When it

reaches the maximum allowed failures, a blackout timer is set for 2 hours. After dialing, if the call is

successful then called number's failure count is set to 0. The allowed values are 0 - 100 inclusive. If this setting

is set to "0", failures are ignored and no blackout will occur. The default is 15.

PPP Hosting Settings

This menu is for configuring settings for hosting a PPP connection on the POTs Dial-Up Modem.

TeleBoss 830 - PPP Hosting Settings
A) PPP Hosting Enabled [OFF]
B) Idle Connection Disconnect (sec) [60]
C) Local (Device) IP Address [192.168.105.1]
D) Remote (Caller) IP Address [192.168.105.2]
E) Firewall [ON]

PPP Hosting Enabled

This is an ON/OFF toggle to enable inbound PPP connection hosting. The default setting is OFF.

Idle Connection Disconnect (sec)

This field sets the number of seconds (0 to 65535) to wait before disconnecting an idle connection. A setting

of 0 means the unit does not disconnect due to an idle connection. The default setting is 60 seconds.

Local (Device) IP Address

This option sets the IP address of the TeleBoss for the PPP session. The default is 192.168.105.1

Remote (Caller) IP Address

This field

sets the IP address of the calling device for the PPP session. The default is 192.168.105.2.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды