manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 129

TeleBoss 830 2.11.370 STD User Manual 

 

Page 129 

 

 
TeleBoss 830 - Audit Log Settings 
A) List Audit Log File 
B) Clear Audit Log File 
C) Enable Audit Log File                [ON] 
D) Maximum File Size                    [32] 
E) Store Reset Events                   [ON] 
F) Store Command Entry                  [ON] 
G) Store Output Activity                [ON] 
H) Store Alarm Actions Taken            [ON] 
I) Store Password Failures              [ON] 
J) Store Logins/Disconnects             [ON] 
K) Store Pass-through Activity          [ON] 
L) Store Inactivity Timeouts            [ON] 
M) Store Polling Activity               [ON] 
N) Store DIP Switch Changes             [ON] 
 

 

List Audit Log File

  

Choosing this option will display the contents of the Audit Log file, if any records exist. 

 

Clear Audit Log File

  

Entering the letter for this selection will purge the records within the Events File.  Records in the Events File 

are deleted immediately when this option is selected. 

 

 

Caution:

 The records in the Events File are deleted immediately when this option is selected. 

 

Enable Audit Log File

  

This is an ON/OFF toggle to enable Audit logging.  The default setting is ON. 

 

Maximum File Size

  

This option is used to set the maximum number of KB the event log can reach before overwriting the oldest 

records.  The available options are 0, 64, 128, 256, 512, and 1024. 

If the setting is 0 then the audit log’s only 

constraint on size will be the available physical memory.  The default is 128. 

 

Store… 

The remaining options are ON/OFF toggles to enable logging of the specific action described.  The default 

setting for all is ON. 

 

 

Audit Log Settings as accessed via Web UI 

To access the Audit Log settings in the Web Interface select the Administration option from the left hand menu 

and select System Logs.  There is a drop down box at the top of the page to toggle the log view between the 

Audit and Event logs. 

 

The Audit log settings are at the bottom of the page. 

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды