Asentria TeleBoss 830 Скачать руководство пользователя страница 77

Страница: 77 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 77

IP Address

Sets the IPv4 address of the unit reachable by nodes on the network interface consisting of the Ethernet

Expansion Card(s). If this is default (0.0.0.0), then each card will still convey Ethernet traffic (acting as

Ethernet switch) among its nodes but those nodes will not be able to communicate with the unit.

Subnet Mask

Sets the IPv4 subnet mask for the Ethernet Expansion network interface. The default is 255.255.252.0

Router Address

This option sets the IPv4 address of the next hop router for this subnet. If set, it will be displayed as an option

in the list of IPv4 default routers.

NAT

This is an ON/OFF toggle to enable/disable network address translation on the forwarded frames. Without

NAT, a server would receive a forwarded frame that is IP-addressed

DHCP Starting IP Address

Sets the starting IP address for serving DHCP addresses on the Ethernet Expansion network interface. If this

is default (0.0.0.0) then the unit will not run DHCP to serve addresses. This address is required for DHCP

server to start and must be on the same subnet as Ethernet Expansion Card IP Address.

DHCP Lease Time (minutes)

Lease time for DHCP clients in minutes (default 60).

DHCP Bootfile Name

This option is used to identify a bootstrap file. Not all DHCP clients support it, others actually require it.

DHCP VoIP TFTP Server

Custom option for Cisco SIP phones

Ethernet Expansion Settings as accessed via Web UI

These same settings can be configured on the Web Interface.  They are located in the Network submenu
under the Networking in the left hand menu.  The “Basics Settings” as covered above are in the middle of the
page.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды