Asentria TeleBoss 830 Скачать руководство пользователя страница 35

Страница: 35 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 35

Notice Boxes

The unit will give informational type notices at the top of the page. These are color coded notices for the user.

Informational notices, such as the unit letting you know something was completed successfully, will be in

green. The notice will display for a few moments and disappear. The "x" can be clicked at any time to close

the notice.

Yellow is a warning color. It will contain a message regarding a system settings change that needs to be

adjusted. Warning notices will also display for a few moments and then disappear. The "x" can be clicked at

any time to close the notice.

A message in red is a warning that the action attempted failed. Red warning notices stay at the top of the

screen until manually closed by the user by clicking the "x" on the right hand side of the notice. The setting

that failed will have the entry field colored red to denote the error.

Alternate Settings Fields

There are some locations which have menu options in the upper sections of the page, which when clicked,

change the available options in the lower entry fields.

The name of the section

whose settings are now

displayed in the lower

settings section will be in

the header over that

section.

To change the settings to

another of the available

menu options, simply click

the menu hyperlink and the

settings fields for the

selected menu option will

display below.

Save your changes before moving to another menu page.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды