manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 89

TeleBoss 830 2.11.370 STD User Manual 

 

Page 89 

 

 

Note: 

User Name and Passwords are case sensitive.  Passwords are masked in all menus and while 

typing them from the command line, for security reasons.  If a user without permissions accesses the 

User Profile Settings menus, they will see all fields in this menu either masked or with no data in 
them.  If they select an option, a message will be displayed that says:  “You do not have permission to 
change this setting

.”

 

 

 

Note:  

When configuring a new user name and an invalid or duplicate user name is entered, the 

TeleBoss responds as follows: 

 

 

 

 

 

Invalid Entry. 
Press any key to continue... 

 

 

 

Note:  

When configuring a new password, the unit will ask you to re-enter the password.  If the 

second entry of the password does not match the first, the TeleBoss will respond as follows: 

 

 

 

Invalid Entry - Confirm Password does not match. 
Press any key to continue... 

 

 

 

Allow User Connection via  

This option displays a menu allowing you to toggle ON or OFF access via Local (Console Port), Modem, 

Telnet, FTP, Real-Time Socket, and the Web interface.  These are abbreviated: LMTFRW and default setting 

for all is ON. 

 

 
TeleBoss 830 - Allowed User Connection Via 
A) Modem                                [ON] 
B) Telnet                               [ON] 
C) FTP                                  [ON] 
D) Local                                [ON] 
E) Real Time Socket                     [ON] 
F) Web                                  [ON] 
 

 

Upon Login then Go To  

This menu selection toggles the action this user will be directed to upon logging in, with the following options:  

COMMAND, PASSTHROUGH and MENU as shown here: 

 

 

Command 

 

 
TeleBoss 
Password: ******** 
READY 
> 

 

 

Menu

 

 
TeleBoss 830 Version 2.11.370 at 830-830000163 
 
1. Pass-Through to I/O 1 
2. Pass-Through to I/O 2 
P. 830 Command Prompt 
M. 830 Setup Menu 
S. 830 Status Menu 
X. Exit (end connection) 
 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды