Asentria TeleBoss 830 Скачать руководство пользователя страница 119

Страница: 119 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 119



Note:

The web UI has configuration options for up to twelve IP/Hosts. In future software releases up to

twelve will be configurable from either interface.

Pager Number n

This menu is used to configure pager call outs used in event actions. Pager call outs can only be used if an

optional POTs dialup modem card is installed in the TeleBoss.

TeleBoss 830 - Pager 1 Settings
A) Pager Type [NUMERIC]
B) Pager Callout Number []
C) Pager ID []
D) Numeric Message []
E) Post Callout Delay (seconds) [15]
F) Post ID Delay (seconds) [5]

Pager Type

This toggles between NUMERIC and ALPHA to select the type of pager to call. The default is NUMERIC.

Pager Callout Number

Set the phone number for the pager.

Pager ID

This function is used only with paging systems where many pagers share the same phone number. This is

common with alphanumeric pagers.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды