manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 140

TeleBoss 830 2.11.370 STD User Manual     

 

Page 140 

 

box to select the correct Settings Key file and click Open.  Once you begin the transfer the unit will 

recognize it, and apply the settings immediately. 

 

 

ASCII 

After an SK set the TeleBoss will prompt "[X]modem or [A]scii?"  Press 

A 

for ASCII.  Using your 

terminal emulator's menus find the option to send a file.  In TeraTerm Click the "File" option in the 

upper left corner and c

hoose "Send File…" and use the pop up box to locate the correct Settings Key 

file and click Open.  Once you begin the transfer the unit will recognize it and apply the settings 

immediately. 

 

4.  (Optional) After the restore is complete type 

SK LOG

 to see a summary of any errors generated 

during an 

SK Set

. 

 

 

Restoring Settings via FTP 

To transfer settings to the TeleBoss using FTP: 

1.  Open a command prompt window on a computer or server that has network access to your TeleBoss. 

2.  Type 

FTP <IP address of unit>

 

3.  You will be prompted for the user name and password.  In order to set settings via FTP you will have 

to use the user name 

omni

 and your master level password. 

4.  Once the 

user credentials have been input you will get: “230 Login accepted.” and an FTP command 

prompt. 

5.  The syntax for receiving files from another machine to the TeleBoss is: 

put [path to file] [filename].  

The path is the absolute path to the file on the other machine including any extensions. Use 

backslashes (\) for path strings.  The file name is the exact name of the file including any extensions 

(.txt).   

 

 
J:\>ftp 192.168.100.244 
Connected to 192.168.100.244. 
220- TeleBoss FTP Server Active (830001122 02/12/17) 
220  Please enter user name to proceed... 
User (192.168.50.100:(none)): omni 
331 Password required for omni 
Password: 
230 Login accepted. 
ftp> put c:\temp\Teleboss.txt 
200 Port OK 
150-Please stand by... 
150 Opening Data Connection...  
226 Transfer complete. 
ftp: 49837 bytes received in 0.04Seconds 1245.93Kbytes/sec. 
ftp>bye 
221 Goodbye. 
J:\> 

 

 
 

Firmware Upgrades  

 

Note:

 Before upgrading it is always a good idea to make a copy of the Setting Keys file in your unit, in 

case settings are lost during the upgrade. This usually does not happen, but it’s better to be safe than 
sorry. 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды