manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 70

TeleBoss 830 2.11.370 STD User Manual     

 

Page 70 

 

Dialup Modem PPP is up instead of the Wireless, then that traffic will go out the Dialup Modem PPP 

interface. 

 

 
TeleBoss 830 - Routing Settings 
A) Static Route Settings - IPv4 
 
Enter your Selection: A 
 
 
TeleBoss 830 - Static Route Settings - IPv4 
A) Route 1 
. . . 
H) Route 8 
 
Enter your Selection: A 
 
 
TeleBoss 830 - Static Route 1 Settings 
A) Enable                               [OFF] 
B) Destination Network                  [0.0.0.0/0] 
C) Gateway                              [0.0.0.0] 
D) Interface                            [NONE] 
 

 

Enable

  

This is an ON/OFF toggle to enable a static route.  The default setting is OFF. 

 

Destination Network

  

Define the destination network notation, i.e., w.x.y.z/s, where 

s

 is the significant bits. The default is 0.0.0.0/0. 

 

To configure a static 

host

 route specify a destination net with sigbits == 32.  To configure a static 

network

 

route specify a destination net with sigbits < 32. 

 

Gateway

  

Enter the IP address of the gateway.  The default setting is 0.0.0.0 

 

Interface

  

This option displays a listing from which to select any one of the interfaces available on this TeleBoss.  The 

default setting is NONE. 

 

You can specify a gateway or interface. If you specify a gateway only, then the frame will be IP-

addressed to the destination subnet and transmitted to the gateway, and the gateway needs to be either 

a local Ethernet subnet or the peer of a PPP connection (be it wireless or PSTN). If you specify an 

interface, regardless of specifying a gateway, then the frame will be transmitted out that interface.  

 

 
TeleBoss 830 - Static Route 1 Interface 
A) None 
B) Ethernet 1 
C) Ethernet 2 
D) Dialup Modem PPP 
E) Wireless Modem PPP 

 

 

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды