Asentria TeleBoss 830 Скачать руководство пользователя страница 24

Страница: 24 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 24

Navigating the Control Interfaces

There are two interface options for command and control of your TeleBoss. The

Command Line Interface

(Command Processor) is used most frequently to control the TeleBoss. The Command Line Interface can be

reach via Serial, Telnet or SSH interface options. Some specific FTP and serial commands and advanced

debugging or control functions can only be accomplished via the Command Line Interface.

The

Web Interface

is an intuitive GUI interface that can be used for routine control and maintenance of your

unit via HTTP or HTTPS using up to date versions of Chrome, Firefox, or Internet Explorer. Simply type the

configured IP address into the browser navigation and you will be presented with a log in page,

http://<IP

address of T830>

https://<IP address of T830>

to use Secure Sockets Layer (SSL). Commands and

Serial Data cannot be entered or viewed via the Web Interface.

Command Line Interface (CLI)

The Command Line Interface, also referred to as the Command Processor, is a text based interface. Specific

commands can be entered to control the unit and access connected devices.

The Command Line Interface can be accessed via Telnet, SSH or serially via IO2. See the Accessing the

TeleBoss

Telnet

section for instructions on accessing the TeleBoss via Telnet or the

Access via a Serial

Connection

for instructions on accessing the unit using I/O2.

This interface is command based. You can give instructions to the unit using specific text commands. Unless

overridden by your terminal emulator, local echo is enabled by default. This means that you will be able to see

commands as you type them. There is a section of the manual which covers all available commands,

Command Reference

The CLI has structured menus and submenus to set up automatic functions. Most of the elements you will

interact with will be under the setup menu which you reach by typing

SETUP

. To select a menu item enter the

corresponding letter next to the item. You will be immediately taken to that items configuration menu. Use

<Enter> or <Esc> to go back a level, or <Ctrl+C> to return directly to the command prompt. See the

Setup

Menu Inputs

section for additional instructions on using this menu system.

CLI Status Pages

The TeleBoss status pages are informational displays. Most of the information that a user would need to know

about the unit is displayed on these screens. This section outlines the different status screens, how to display

them and defines the displayed fields.

General Status

You reach this status screen by typing

STATUS

at the command prompt followed by <Enter>.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды