Asentria TeleBoss 830 Скачать руководство пользователя страница 10

Страница: 10 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 10

Telnet

Once the IP address has been configured, clicking the Telnet button will open a connection to the TeleBoss'

Command Line Interface using your default Telnet client, if one is configured for your operating system. If

your computer does not have a Telnet client configured any terminal emulator such as Putty

(

http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

) or TeraTerm

(

http://ttssh2.sourceforge.jp/index.html.en

) can be used.

If a default telnet client has been configured, you can simply navigate from your computer's command

window:



Type "

Telnet

" at the Windows command prompt.



Then type "

Open <IP Address>

". This will take you to the TeleBoss Command Interface.



Type in the password for the unit and return. See the

Default Password

section for login instructions.



See the

Command Line Interface

section for instructions on how to control your TeleBoss using this

interface.



To exit from the TeleBoss Command Line In

terface type “

bye

”.



To exit from the Windows Telnet client type “

quit

”.

Web

Once the IP address has been assigned, clicking the Web button opens an HTTP (web) connection to the

device using your default browser. See the

Default Password

section for log in instructions. The Web

Interface can also be reached by typing the configured IP address into an internet browser's address bar.

Contact

Asentria Technical Support

for any questions or assistance with OmniDiscover. Refer to the

Telnet

Feature Guide

on the Asentria Information Portal for further information regarding a number of different types

of Telnet connection options.

Default Passwords

The TeleBoss uses a very flexible system for managing users, passwords, and access rights. By default, the

following five user profiles are enabled. Note that if a password is defined without a user name, the User

Name defaults to User

. All passwords are masked: ********

The default settings are configured to low security for your convenience in setup. It is highly recommended

that you change these passwords and record them in a secure location. The username and passwords are

configured in the Security Settings menu under

User Profile Security Settings

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды