Asentria TeleBoss 830 Скачать руководство пользователя страница 21

Страница: 21 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 21

for I/O 2 Port Mode is Command, and someone flips SW4 to the UP position, the Mode is immediately set

to Data.

Buttons

The only button on the T830 is the Reset button located on the back panel next to the left of serial port I/O 2.

The Reset button can be used for two different functions:

1) To reset the T830

– press the Reset button for approximately 1 second and T830 will be begin the

reboot process as described in the

Power Up Sequence

section on the next page.

2) To activate the

Button Unlock

feature which resets the username and password back to default.

Optional Hardware

The TeleBoss has a wide variety of optional cards and accessories. Options include DC Power Input, 64MB

logging database for text records, an internal POTS modem, as well as two types of Run-time battery backup

options.

The various optional expansion cards have appropriate wiring and accessories including with the shipment.

I/O points and Expansion Cards

The expansion cards in the two or six expansion card slots can be configured with multiple options. The

terminal block ports will be marked to indicate how the slot card is configured. A single card can have more

than one type of I/O option. The Expansion cards that are currently available are:

Expansion Cards - Communications Related

Catalog #

Wireless EDGE Modem (not recommended for US market)

Wireless LTE Cat M1 Verizon

ML1V

Wireless LTE Cat M1 PTCRB - AT&T and T-Mobile

ML1P

Wireless LTE Modem - for EU with GPS

MLEU

Wireless LTE Modem - for EU with GPS, CAT3, FAST EXP CARD ML3EF

Dial-Up Serial Modem slot card

4X RS232 Serial Port

2X RS485 2X RS232 Port

2DS2S

2X RS485, 5v Pwr, Voltage, F - Fuel Resistive, 2X Form C Relays

2DS5P1V1F2RC

4X EventSensor Expansion Card

4ES

4X 10/100 Ethernet Port (up to 2 per unit)

8X 10/100 Ethernet Port (up to 2 per unit, each card occupies 2

vertical slots requires a 6 Expansion slot TeleBoss unit

Secure Access Ethernet Card, 4E Co-processor

SAEC

GPS Receiver

GPS

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды