manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 97

TeleBoss 830 2.11.370 STD User Manual 

 

Page 97 

 

Alarm / Event Definitions 

This will display a menu tree which contains the event settings options.  The Event section is used to set 

up actions the TeleBoss should take in response to sensor events, scheduled events, serial handshaking 

events as well as actions the unit should take in response to a reset or a power cycle. 

 

 
TeleBoss 830 - Alarm/Event Definitions Menu 
A) Class Table 
B) Data Alarm/Filter Settings 
C) EventSensor Device Settings 
D) No-Data 1 Alarm Settings             [OFF] 
E) No-Data 2 Alarm Settings             [OFF] 
F) Percent Full Alarm Settings          [OFF] 
G) Scheduled Event 1 Settings           [OFF] 
H) Scheduled Event 2 Settings           [OFF] 
I) CPE Alarm Settings 
J) Data Filter Action                   [REJECT] 
K) Event Message Settings 
L) Reset Event Settings                 [OFF] 
 

 

Class Table

  

The Class Table option displays the menu for configuring event severity classification settings. 

 

Data Alarm/Filter Settings

  

This option displays the menus for configuring serial data event monitors. 

 

EventSensor Device Settings

  

This option displays the menus for configuring internal and external sensors. 

 

No-Data n Alarm Settings

 

These selections display the menus for configuring alarms based on period of time when no-data is received 

on a specific serial port. 

 

Percent Full Alarm Settings

  

This option displays the menu for configuring alarms based on how full the call record database of the 

TeleBoss is. 

 

Scheduled Event n Settings

  

These selections display the menus for configuring alarm notifications for specific times and days of the week. 

 

 

CPE Alarm Settings

  

This option displays the menu for configuring Customer Premises Equipment (CPE) monitoring functions.  

This function is referred to as "Ping Alarms" on the Web interface. 

 

Data Filter Action

  

The Data Filter Action option toggles between REJECT and ACCEPT to indicate whether data filters are 

configured to reject or accept specific incoming data string(s).  The filters are configured in the Data 

Alarm/Filter Settings / Data Alarm Settings / Alarm/Filter Page 

n 

/ 

Alarm/Filter 

n

 

 menu.  The default setting is 

REJECT. 

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды