manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 103

TeleBoss 830 2.11.370 STD User Manual 

 

Page 103 

 

Data Alarm/Filter Settings 

This is the menu for configuring individual data alarms or filters. Refer to the 

Data Alarm and Event 

Configuration Feature Guide

 on the Asentria Product Information Portal or contact 

Asentria Technical Support

 

for more information. 

 

 
TeleBoss 830 - Data Alarm/Filter Settings 
A) Alarm/Filter Page 1 (Alarms 1-16) 
   ... 
M) Alarm/Filter Page 13 (Alarms 193-200) 
 

 

Data alarms are configured by selecting an option from the main Data Alarm/Filter Settings menu, then 

selecting one of the options which will give you a group of 16 data alarm/filters (1-16, 17-32, etc).   This will 

display a menu where you can select from those 16 data alarm options as follows: 

 

 
TeleBoss 830 - Data Alarm/Filter Settings 
A) Alarm/Filter 1           []                      [OFF]  [ALARM] 
   ... 
P) Alarm/Filter 16          []                      [OFF]  [ALARM] 
Q) Next Alarm/Filter Page 
R) Setup Alarm/Filter Fields 
S) Display Alarm Status 
T) Exit Upon True Data Alarm                        [OFF] 
 

 

Alarm/Filter n

  

These options will display a

 menu where an individual data alarm or filter can be configured. 

 

Next or Previous Alarm/Filter Page

  

These options will display either the next or previous set of 16 Data Alarm/Filters. 

 

Setup Alarm/Filter Fields

  

This option will display the identical 

Data Alarm Field Settings

 menu as described above.  This is simply an 

easy way to access that menu without having to exit back through the previous menus.  

 

Display Alarm Status  

This selection displays real time information on data event monitors you've configured. 

 

Exit Upon True Data Alarm  

This is an ON/OFF toggle to set whether the TeleBoss will stop processing more data event evaluations on a 

single record after it has found one match.  This should be disabled if it is possible to have more than one 

event in a record.  This is a global setting 

– it applies to ALL configured data alarms.  Default setting is OFF. 

 

 

Data Alarm/Filter n Settings 

This is the menu for configuring individual data alarms or filters. Refer to the 

Data Alarm and Event 

Configuration Feature Guide

 on the Asentria Product Information Portal or contact 

Asentria Technical Support

 

for more information. 

 

 

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды