Asentria TeleBoss 830 Скачать руководство пользователя страница 115

Страница: 115 / 157

TeleBoss 830 2.11.370 STD User Manual

Page 115

These fields allow you to add or d

elete specific dates when this Scheduled Event should “take the day off”.

For example Christmas is a day you might want to add here. Select Add Exclusion and type in

12/25

. To

delete a date, you select Delete Exclusion and type in the date you want to remove. After an exclusion date is

added it appears in the brackets at the bottom of the menu. 15 dates can be entered to be excluded.

Scheduled Event Settings as accessed via Web UI

The Scheduled Event Settings are located under the Events option in the left hand menu. The time should be

entered in HH:MM in 24 hour clock format.

CPE Alarm Settings

This menu is used for configuring Customer Premises Equipment (CPE) monitoring functions. Configure

the equipment to monitor under Network Settings/

CPE Settings

. Contact

Asentria Technical Support

for

more information.

This functionality is called Ping Alarm in the Web Interface.

TeleBoss 830 - CPE Alarm Settings
A) Alarm Enable [OFF]
B) Alarm Actions []
C) Alarm Trap Number [511]
D) Alarm Class [Info]
E) Return to Normal Actions []
F) Return to Normal Trap Number [511]
G) Return to Normal Class [Info]

Alarm Enable

This is an ON/OFF toggle to enable the CPE Down Event. The default setting is OFF.

Alarm Actions / Return to Normal Actions

Choosing one of these options will display the Actions List, a menu where the action string for the event is

configured. This field will be empty [ ] if no actions have been configured, and will show [*SET*] if one or

more actions have been configured. Refer to the

Actions List

chapter for more information.

Содержание TeleBoss 830






























































































































































Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды

Asentria TeleBoss 830, Руководство пользователя

Результаты поиска

Содержание TeleBoss 830

Отзывы:

Бренды по названию

Популярные бренды