manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 112

TeleBoss 830 2.11.370 STD User Manual     

 

Page 112 

 

Schedule n Duration  

These fields set the number of minutes (0-65535) the unit will wait without receiving data before alarming. 

 

Apply Alarm on Days  

This option displays a menu where the seven days of the week are listed, and each can be toggled ON or 

OFF to designate whether this particular No-Data alarm is active on that day. The default setting is ON for 

Monday thru Friday, and OFF for Saturday and Sunday. 

 

Enable Ports  

This selection displays a menu where the installed serial ports are listed and each can be toggled ON or OFF 

to designate whether this particular No-Data alarm is active on that port. The default setting is OFF for all 

ports. 

 

Add Exclusion / Delete Exclusion  

These fields allow you to add or delete specific dates when this No-

Data Alarm should “take the day off”. For 

example Christmas is a day you might want to add here. Select Add Exclusion and type in 12/25. To delete a 

date, select Delete Exclusion and type in the date you want to remove. After an exclusion date is added it 

appears in the brackets at the bottom of the menu. Up to fifteen dates can be entered to be excluded. 

 

 

No-Data Alarm Settings as accessed via Web UI 

The No-Data Alarms Settings are located in the Events menu on the left hand menu.  Use the drop down in 

the header to toggle to the second No-Data Alarm Settings page. 

 

 

 

 

Percent Full Alarm Settings 

Percent Full Alarms send an alarm when the Teleboss buffer reaches a certain Percentage of full memory. 
This feature can send an alarm message before the unit fills to capacity. 

 

 
TeleBoss 830 - Percent Full Alarm Settings 
A) Alarm Enable                         [OFF] 
B) Percent Full Threshold               [80] 
C) Alarm Actions                        [] 
D) Alarm Message                        [DB Exceeds Threshold] 
E) Alarm Class                          [Info] 
F) Trap Number                          [501] 
 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды