manualshive.com logo in svg

Asentria TeleBoss 830, Руководство пользователя

Поделиться
Скачать
Asentria TeleBoss 830 Скачать руководство пользователя страница 127

TeleBoss 830 2.11.370 STD User Manual 

 

Page 127 

 

Event Log Settings 

The Event Log is a record of all data events that occur within the TeleBoss. 

 
The Event Log overwrites itself when it becomes full. “Full” has meaning that you can control with the 
Maximum File Size setting. This setting controls the maximum size (in KB) to which the file should be limited. 

If the setting is 0 then the audit lo

g’s only constraint on size will be the available physical memory. 

 

 
TeleBoss 830 - Event Log Settings 
A) List Events File 
B) Clear Events File 
C) Enable Events Log File               [ON] 
D) Maximum File Size                    [32] 
E) Store Data Alarm Records             [OFF] 
F) Store Sensor Events                  [OFF] 
G) Date/Time Stamp Data Alarm Records   [OFF] 
H) Prepend Data Alarm Name              [OFF] 
 

 

List Events File

  

Choosing this option will display the contents of the Events File, if any records exist. 

 

Clear Events File

  

Entering the letter for this selection will purge the records within the Events File.  

 

 

Caution:

 The records in the Events File are deleted immediately when this option is selected. 

 

Enable Events Log File

  

This is an ON/OFF toggle to enable Event logging.  The default setting is ON. 

 

Maximum File Size

  

This field will set the maximum number of KB the event log can reach before overwriting the oldest records.  

The available options are 0, 64, 128, 256, 512, and 1024.  The default setting is 32. 

 

Store Data Alarm Records

  

This option is an ON/OFF toggle to enable storing data alarm records.  The default setting is OFF. 

 

Store Sensor Events

  

This is an ON/OFF toggle to enable storing records generated by environmental sensors. The default setting 

is OFF. 

  

Date/Time Stamp Data Alarm Records

  

This is an ON/OFF toggle to prepend a Date/Time stamp to the beginning of data alarm records.  The default 

setting is OFF. 

 

Prepend Data Alarm Name

  

This is an ON/OFF toggle to prepend the name of the Data Alarm to the beginning of the data alarm record.  

This aids in identifying which Data Alarm an alarm record is associated with.  The default setting is OFF. 

 

 

Содержание TeleBoss 830






























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды