manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 32 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 32

1-5

IM 701210-05E

Names and Functions of Parts

1

Left Side Panel

DL750

REC  LEVEL  

V

O

LUME

VO
IC

E

 I

N

/OUT/SW

GP-IB  (IEEE488)

ON

OFF

100-120V/200-240V  A

C

300V

A  MAX  50/60Hz

PO

WER

100B

A

SE-TX

VIDEO OUT (SV

G

A)

SERIAL (RS-232)

USB

USB PERIPHERAL

LOGIC  A

LOGIC  B

GO/NO-GO

TRIG  OUT/

EXT CLK IN

TRIG IN

LINK

AC
T

SCSI

MODEL

NO.

SUFFIX

Made  in  Japan

Pr

otect  the  Instrument  fr

om  vibration  or  shoc

k  when  po

wer  is  ON

(especiall

y  f
o

r  internal  har

d

  disk  type).

CA
UTION

WA

R

NING

Do   not   operate  without   reading    saf

ety  precautions  In   user`s   man

u

al .

Vent holes

GP-IB connector

Used when carrying out 
communications via the 
GP-IB interface.  
For a description of the 
communication function, 
see the 

Communication 

Interface User’s Manual

.

Voice memo function terminal

Used when recording voice while data acquisition is in 
progress using the voice memo function and recording 
voice along with screen image data.  For a description 
of their use, see sections 7.9 and 13.19.

Floppy disk drive, Zip disk drive, 
(DL750 only) or PC card drive

Used when saving data to a floppy 
disk, Zip disk, or PC card.
For a description of their use, 
see section 13.1.

Video signal output 
terminal

Outputs the displayed 
image using SVGA RGB 
signals.  For a description 
on how to use the terminal, 
see section 14.4.

Ethernet port (100BASE-TX)

Used when connecting to a LAN.
For a description of how to use 
the port, see section 16.1.

Power switch

For the power ON/OFF 
operation, see section 3.4.

Name plate

Power connector

For details on 
connecting the power, 
see section 3.4.

SCSI interface connector

Used when connecting to a SCSI 
device such as a SCSI hard disk.
For a description of how to use 
the connector, see section 13.4.

USB connector for connecting 
to a PC

Used when connecting a PC with a USB 
interface.  For a description of how to 
use the connector, see communication
interface user’s manual.

GO/NO-GO I/O connector and 
external start/stop input connector

Outputs the GO/NO-GO determination 
I/O signals.
Also used to externally control the 
start/stop of the DL750.
For a description of how to use the 
terminal, see sections 11.10 and 14.5.

USB connector for connecting 
peripheral devices

Used when connecting a USB keyboard, 
USB printer, USB mouse, or USB storage
device.
For a description of how to use the 
connector, see sections 4.3 and 12.3.

Logic signal input connector

Used when measuring logic signals.
For a description of how to use the 
connector, see section 3.11.

Trigger output/external clock 
input terminal

RS-232 interface

Used when inputting external 
trigger signals.  
For a description of how to 
use the terminal, 
see section 14.1.

Used when outputting trigger signals 
externally or inputting clock signals.
For a description of how to use the 
terminal, see sections 14.2 and 14.3.

Used when carrying out 
communications with a PC via 
the RS-232 interface.
For a description of the 
communication function, 
see the 

Communication 

Interface User’s Manual

.

Trigger input terminal

DC Power Supply Model (DL750 only)

Power supply status LED

Displays the status of the 
AC power supply or DC 
power supply.
For details on the status 
indicator, see section 3.4.

Power switch (AC)

For the power ON/OFF 
operation, see section 3.4.

Power switch (DC)

For the power ON/OFF 
operation, see section 3.4.

AC power connector

For details on connecting 
the power, see section 3.4.

DC power connector

For details on connecting 
the power, see section 3.4.

1.1 Top Panel, Front Panel, Right Side Panel, and Left Side Panel

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments