manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 293 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 293

7-27

IM 701210-05E

Acquisition and Display

7

Erasing Voice Memos

The recorded voice memo can be erased.  This operation is performed when a voice

memo was recorded while waveform acquisition was in progress, but you wish to save

the waveform data without the voice memo.

After step 16 of this section, press the 

Erase 

soft key.  The voice memo is erased, and

the voice memory indicator value on the screen is cleared.

Note

Once a voice memo is erased, it cannot be recovered.  Use caution when erasing a voice
memo.

Explanation

A voice memo can be recorded while waveform acquisition is in progress (when in roll

mode display) by connecting an earphone microphone with a PUSH switch to the DL750/

DL750P.

Setting the Mode

To enable the voice memo function, set Mode to ON.

When turned ON, a voice memory indicator is displayed at the lower right corner of the

screen.

Displaying Event Waveforms

The event waveform (Voice bit of the event waveform) indicates the record interval of the

voice memo.  The interval during which a voice memo is recorded is from the rising edge

to the falling edge of the event waveform.  For the procedure of setting event waveforms,

see section 5.21.

Waveform for recording 
a voice memo

Event waveform

Record start

Record start

Record stop

Record stop

Precautions Regarding the Voice Memo Function

• If the record length setting is set long in the ACQ menu causing the number of

channels that can be used to 3 channels or less, event waveforms are not displayed.

In this case, the voice memo function cannot be used.

• If the voice memo function is OFF (Mode: OFF) even when the event waveform

display is ON (Event Display: ON), event waveforms are not saved when waveform

data is saved.  In addition, even if a voice memo is recorded during waveform

acquisition, if the voice memo function is turned OFF at the time waveform data is

saved, event waveform data/voice data will not be saved.

• In realtime recording, if the valid number of channels

1

 is 3 channels or less, event

waveforms cannot be used.  In this case, the voice memo function cannot be used.

1. Valid number of channels signify the number of channels that are turned ON excluding

MATH1 to MATH8 channels.  However, for LOGIC A and LOGIC B, the number of channels
is counted as 1 regardless of whether one of the channels is ON or both channels are ON.

7.9 Using the Voice Memo Function

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments