YOKOGAWA 701210 User Manual Download Page 281

Page: 281 / 747

7-15

IM 701210-05E

Acquisition and Display

• Displaying the List of Captured Waveforms: Show Map

The number of the acquired waveform and the trigger time are listed. You can also

select the desired waveform number to display the list.

• Send Mail

When turned ON, a mail is sent to the mail address specified in NetWork settings

each time a waveform is acquired. For details, see section 16.5, "Sending Periodic

Mail or Action Mail."

Mark

The

mark indicates the position of the sub waveform specified by Capture Num at the

top section of on the main waveform window. However, when waveforms are being

acquired in the Auto mode, the

mark is not displayed for sub waveform positions that

exceed the end of the main waveform.

Note

Key response is slowed down when waveform acquisition is in progress using the dual
capture function.

Notes When Using the Dual Capture Function

• The dual capture function can be used only when the trigger mode is set to Auto or

Log.

• The maximum record length of the main waveform varies depending on the model as

follows: The dual capture function cannot be used at record lengths that exceed the

maximum record length.

Standard model: 5 M

/M1 model: 10 M

/M2 model:

50 M

/M3 model: 100 M

• The dual capture function cannot be used if the acquisition mode of the main

waveform is Average.

• The dual capture function and the realtime recording function cannot be used

simultaneously.

• The dual capture mode cannot be changed while waveform acquisition is in progress.

• If you restart measurements after acquiring waveforms, all the waveforms that were

acquired before changing the mode are cleared.

• The dual capture function cannot be applied to X-Y waveforms.

• Saving/loading of the waveforms acquired using the dual capture function is

performed simultaneously for the main waveform and the sub waveform. For details

on the saving/loading of the waveform, see section 13.7, “Saving/Loading Waveform

Data.”

• The dual capture function cannot be used if the time base is set to external clock.

• Accumulate function cannot be used.

• Cursor measurements and automated measurement of waveform parameters are

suspended while waveforms are acquired using the dual capture function.

• Automated measurement of waveform parameters and computations cannot be

performed on the sub waveform.

• When the sub waveform is displayed, cursor measurements are made on the sub

waveform.

7.6 Using the Dual Capture Function

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 281 / 747

Search results

Summary of Contents for 701210

Reviews: