YOKOGAWA 701210 User Manual Download Page 109

Page: 109 / 747

3-6

IM 701210-05E

Types of Input Modules

The following nine types are available.

• High-Speed 10 MS/s, 12-Bit Isolation Module: 701250 (HS10M12)

• High-Speed 10 MS/s, 12-Bit Non-Isolation Module: 701255 (NONISO_10M12)

• High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS): 701260 (HV (with RMS))

• Universal (Voltage/Temp.) Module: 701261 (UNIVERSAL)

• Universal (Voltage/Temp.) Module (with AAF): 701262 (UNIVERSAL (AAF))

• Temperature, High Precision Voltage Isolation Module: 701265 (TEMP/HPV)

• Strain Module (NDIS): 701270 (STRAIN_NDIS)

• Strain Module (DSUB, Shunt-Cal): 701271 (STRAIN_DSUB)

• Acceleration/Voltage Module (with AAF): 701275 (ACCL/VOLT)

• Frequency Module: 701280 (FREQ)

Precautions to Be Taken When Installing or Removing Input Modules

• Switching the installed input module with a different module and turning ON the power

initializes the settings on that channel. To save the settings, specify the destination

media and save the values (see section 13.8, “Saving/Loading Setup Data”).

Installation Procedure of Modules

Check that the power switch on the left side panel is OFF.

Check the channel number indicated above the slots for installing the input

modules on the right side panel of the instrument. Then, install the module

along the guide.

Holding the handles on the top and bottom of the input module, press hard until

it clicks in place.

If there is a cover plate on the slot in which to install the module, remove the

cover plate, first.

Make sure to screw the two locations, top and bottom, of the input module firmly

into place (screw tightening torque: 0.6 N•m).

Turn ON the power switch.

Check to see that the correct input module name is displayed at the

corresponding channel number in the overview screen. If it is not correct,

remove the module according to the steps in “Removal” shown below, and

reinstall the module according to steps 1 to 3 shown above.

For the procedure in displaying the overview screen, see to section 18.4,

“Checking the System Conditions (Overview).”

Guide

3.3 Installing Input Modules

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 109 / 747

Search results

Summary of Contents for 701210

Reviews: