YOKOGAWA 701210 User Manual Download Page 187

Page: 187 / 747

5-27

IM 701210-05E

Horizontal and Vertical Axes

5.14 Setting the Time Base (Internal Clock/External Clock)

CAUTION

Applying a voltage exceeding the maximum allowable input voltage to the TRIG

OUT/EXT CLK IN terminal may damage the input section.

Setting Pulse/Rotate

You can specify the number of pulses of the external signal that is to correspond to one

mechanical rotation (one cycle).

Range of the number of pulses: 1 to 24000

Notes When Sampling Using the External Clock Signal

• You cannot set the acquisition mode to envelope or box average.

• You cannot display waveforms in roll mode.

• No function is provided for frequency-dividing the clock signal.

• Since the time axis setting cannot be changed, change the record length setting or

zoom in on the time axis if you want to change the display range of the time axis.

• The time measured by the cursor measurement or automated measurement of

waveform parameters is expressed in terms of the number of pulses of the clock

signal. No unit is displayed.

• Realtime recording to the internal hard disk cannot be selected.

• Saving data using the dual capture function is not possible.

• The following trigger settings are invalid.

• Trigger delay

• Hold off

• B > Time, B < Time, and B Time Out trigger

• Period trigger

Maximum Sample Rate of Each Module

If the sample rate of the DL750/DL750P is set higher than the maximum sample rate of

the module, the data is updated only at the maximum sample rate of the module.

Consequently, all of the data within the data update interval of the module are the same

data.The maximum sample rate of each module is as follows:

Maximum Sample Rate of Each Module

Module

During Internal Clock

During External Clock

701250/701255:

10 MHz

1 MHz

701251:

1 MHz

701260/701270/701271/

100 kHz

701275/:

701261/701262 (measuring voltage):

100 kHz

(measuring temperature): 500 Hz

500Hz

701280:

25 kHz

701265:

500 Hz

DSP channel:

100 kHz

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 187 / 747

Search results

Summary of Contents for 701210

Reviews: