YOKOGAWA 701210 User Manual Download Page 135

Page: 135 / 747

3-32

IM 701210-05E

3.13 Connecting Sensors to the Frequency Module

Sensors and Signal Output Sources That Can Be Connected

The table below shows the sensor and signal output source that can be connected.

Appropriate input presets are provided for each sensor and signal output source. For the

setup procedure of presets, see page 5-40.

Sensor and Signal Output Source

Preset Name

5-V logic signal, 5-V output sensor, and sensor with TTL output

Logic 5V

3-V logic signal and 3-V output sensor

Logic 3V

12-V driven relay/sequence circuit and 12-V driven sensor

Logic 12V

24-V driven relay/sequence circuit and 24-V driven sensor

Logic 24V

Sensor/Encoder that outputs positive and negative voltages and sensor

ZeroCross

that outputs sine waves

100-VAC power supply (connected via the isolated probe (700929))

AC100V

200-VAC power supply (connected via the isolated probe (700929))

AC200V

Power-generating electromagnetic pickup

EM Pickup

Open collector output (0 to 5 V output) and contact output

Pull-up 5V*

For the internal equivalent circuit for “Pull-up 5V,” see page 5-50.

Precautions to Be Taken When Connecting to Sensors or Signal Output Sources

CAUTION

• The maximum input voltage for direct input is indicated below. Applying a

voltage exceeding this value can damage the input section. If you are applying

high voltage that exceeds 42 V, be sure to use the isolated probe (700929).

Maximum input voltage: 42 V (DC+ACpeak)

(CAT I and CAT II)

• The minimum input voltage is 0.2 Vpp. At voltage amplitude less than 0.2 Vpp,

the measured values may be unstable.

• Attach/Remove the sensors after confirming that the rotating object to be

measured is stopped.

• Set the preset to electromagnetic pickup (EM Pickup) only when using the

electromagnetic pickup.

Connecting the Electromagnetic Pickup

• The DL750/DL750P allows power-generating electromagnetic pickup to be connected

directly. The DL750/DL750P does not support electromagnetic pickups that require

external power supply or those that require a terminator at the output.

• To connect electromagnetic pickups, use BNC cables. Use cables that are

appropriate for the electromagnetic pickups being used.

• When the input is set to electromagnetic pickup, determination is not made on

whether the input voltage level exceeds the specified input voltage range. Therefore,

the LEDs (see page 3-7) do not illuminate even when the input voltage level is over

range.

701280 (FREQ)

Power-generating

electromagnetic pickup

Rotating object

to be measured

BNC connector

DL750/DL750P

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 135 / 747

Search results

Summary of Contents for 701210

Reviews: