manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 210 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 210

5-50

IM 701210-05E

Explanation

Setting the Input: Input Setup

Preset

Select a preset to automatically enter settings appropriate for the signal (Some items

need to be manually entered).  If you select User (user-defined), all the setup items can

be set arbitrarily.  The following 10 presets are available.  For details on the settings of

each preset, see appendix 13.

• Logic 5V, Logic 3V, Logic 12V, and Logic 24V

Use this preset when the output from the sensor or other equivalent item changes in

the range of 0 V to 5 V (or 3 V, 12 V, or 24 V: supply voltage applied to the sensor).

The voltage range is automatically set to the optimum voltage range, and the

threshold level is automatically set to one-half the voltage.

• Pull-up 5V

Use this preset when the sensor output is open collector or contact output.  The pull-

up function is enabled only when this preset is selected.  The pull-up voltage is

approximately 5 V, and the pull-up resistor is 4.7 k

Ω

.  If you turn pull-up ON, set the

input voltage in the range of 0 V to 5 V.  If the input voltage exceeds this range, the

protection circuit is tripped and the pull-up resistor is automatically cut off.

• ZeroCross

Use this preset when the input voltage changes around 0 V.  The input coupling is

automatically set to AC, and the threshold level is automatically set to 0 V.  When

setting the voltage range, be sure that the maximum amplitude does not exceed the

voltage range.

• AC100V or AC200V

Use this preset when measuring the supply voltage of 100-V or 200-V power supply

systems.  The probe type is automatically set to 10:1; the voltage range is

automatically set to a value suitable for the input voltage and probe factor; and the

coupling is automatically set to AC.  Be sure to use the isolated probe (700929) when

measuring the power supply voltage.

• EM Pickup: Electromagnetic Pickup

Use this preset when connecting the electromagnetic pickup directly.  The voltage

range is automatically set to 

±

1 V, and the threshold level is automatically set to 0 V.

• User: User-defined

Use this preset when entering the input conditions arbitrarily.  Pull-up cannot be

specified.

Note

•

When measuring high voltage exceeding 42 V (AC+DCpeak) on the 701280 (FREQ), be
sure to use the isolated probe (700929).

•

Use EM Pickup only when connecting the electromagnetic pickup.

•

When set to EM Pickup, the LEDs of the frequency module do not illuminate in red even
when the range is exceeded.

•

The DL750/DL750P does not support electromagnetic pickups that require power supply
or those that require terminators at the output.  For these types of electromagnetic pickup,
furnish appropriate measures on the sensor end.

•

The output from the electromagnetic pickup must be within 42 V

P-P

.  The minimum

sensitivity is 0.2 V

P-P

.  If the output is less than the minimum sensitivity, the measured

values may be unstable.

•

When using the pull-up function, do not let the voltage exceed the 0 to 5 V range.  If the
voltage exceeds the range, the protection circuit will be tripped, and the pull-up circuit will
be cut off.

5.19 Setting the Frequency (Number of Rotations, Period, Duty Cycle, Power Supply Frequency,
Pulse Width, Pulse Integration, and Velocity) Measurement

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments