manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 107 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 107

3-4

IM 701210-05E

Do Not Install the Instrument in the Following Places.

• In direct sunlight or near heat sources.

• Where an excessive amount of soot, steam, dust, or corrosive gas is present.

• Near strong magnetic field sources.

• Near high voltage equipment or power lines.

• Where the level of mechanical vibration is high.

• In an unstable place.

Installation Position

Place the instrument in a horizontal position or with the rear panel facing down.  When

using the stand, pull it until it locks (see the lower left figure).  To retract it, press the

stand backward while pressing it inward.

DL750

Installed with the rear panel facing down

Installed horizontally

Installed using the stand

DL750P

Installed with the rear panel facing down

Installed horizontally

Installed using the stand

CAUTION

Do not use the Zip drive when the instrument is placed on the stand, as it may

damage the data on the Zip disk.

Rubber Feet

If the instrument is installed in a horizontal position as shown in the figure above, rubber

stoppers can be attached to the feet to prevent the instrument from sliding.  One set (four

pieces) of rubber feet are included in the package.

3.2 Installing the Instrument

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments