manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 122 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 122

3-19

IM 701210-05E

  Making Preparations for Measurements

3

Precautions to Be Taken When Using Current Probes

When connecting the current probe to the probe power supply terminal on the right side
panel, make sure that the current does not exceed the range shown below.  Otherwise,
the DL750/DL750P operation may become unstable due to the activation of the

excessive current protection circuit of the power supply.

A

(Total current consumption of A through D)

 ≤ 

800 mA

When each terminal is assigned names A through D

PROBE

POWER

(   12V)

B

C

D

Specifications of the Probe Power Supply Terminals (Optional)

Item

Number of probes that can be used

4

Probes that can be used

Current probe (700937, 701930, 701931, and 701933)

Number of current probes that can be used

700937 (15 A): Up to 4
701930 (150 A): Up to 2
701931 (500 A): 1
701933 (30 A): Up to 2

Supply voltage

±

12 V  2 outputs (up to a total of 800 mA)

When using the current probe, the number of probes that can be used is limited by the

current generated by the device under measurement (current measured by the current
probe).  The characteristics of the measured current versus the current consumption of
an active probe that can be connected to the DL750/DL750P are shown below.

-250

-200

-150

-100

-50

-15

-10

-5

0

5

10

15

0

50

100

150

200

250

Current probe (700937)

Current consumption [mA]

Measured current [A]

Positive 
current

Negative 
current

-400

-300

-200

-100

-150

-100

-50

0

50

100

150

0

100

200

300

400

Current probe (701930)

Current consumption [mA]

Measured current [A]

Positive 
current

Negative 
current

AC (f=50 Hz)

DC

AC (f=50 Hz)

DC

-500

-400

-300

-200

-100

-500 -400 -300

0

100

200

500

0

100

200

300

400

500

Current consumption [mA]

Measured current [A]

Positive 
current

Negative 
current

-200 -100

300

400

Current probe (701931)

AC (f=50 Hz)

DC

Positive 
current

Negative 
current

Current probe (701933)

Current consumption [mA]

Measured current [A]

-50     -40     -30    -20     -10      0       10      20      30     40      50

600

500

400

300

200

100

0

-100

-200

-300

-400

-500

-600

AC (f=50 Hz)

DC

For details on the usage conditions of each probe, see "Relationship between the current

being measured and probe's current consumption" on the following Web page.

http://www.yokogawa.com/tm/probe/

3.6 Connecting Probes

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments