YOKOGAWA 701210 User Manual Download Page 211

Page: 211 / 747

5-51

IM 701210-05E

Horizontal and Vertical Axes

The following 10 input setup items are available.

• Voltage Range: V Range

Select the input voltage range (

FS) from the following:

• When the probe attenuation is set to 1:1

1 V,

2 V,

5 V,

10 V,

20 V, or

50 V (

FS)

• When the probe attenuation is set to 10:1

10 V,

20 V,

50 V,

100 V,

200 V, or

500 V (

FS)

• Coupling

Set the input coupling to DC or AC.

The description is the same as with the input coupling of other modules. See the

functional explanation given in “Input Coupling” on page 2-8 and the explanation given

in section 5.5.

• Probe Type

Select 1:1 or 10:1.

The description is the same as with the probe type of other modules. See the

functional explanation given in “Probe Type” on page 2-9 and the explanation given in

section 5.6.

• Bandwidth Limit

Set the bandwidth limit to 100 Hz, 1 kHz, 10 kHz, 100 kHz, or Full. You cannot select

Full when the preset is set to AC100V or AC200V.

• Threshold Level

Set the level within FS of the input voltage range. The resolution is a value

corresponding to 1% of FS.

• Hys (Hysteresis)

Set the hysteresis to

1%,

2.5%, or

5% of the FS of the input voltage range.

• Slope

Select (rising) or (falling).

• Chatter Elimination

Eliminates the chatter that occurs such when the contact input is turned ON/OFF.

The changes in the signal over the specified time can be discarded. Set the interval

in the range of 0 to 1000 ms (1-ms resolution). When 0 ms is selected, the chatter

elimination function is turned OFF.

Chattering elimination is effective against both the rising and falling edges.

• Pull Up

You can turn ON/OFF pull-up only when the preset is set to Pull-up 5V. Pull-up is not

possible in other presets.

When using pull-up, set the input voltage in the range of 0 V to 5 V. If a voltage exceeding

this range is applied, the internal protection circuit will cut off the pull-up circuit.

Internal equivalent circuit when using pull-up

+5V

4.7 k

Ω

990 k

Ω

10 k

Ω

5.19 Setting the Frequency (Number of Rotations, Period, Duty Cycle, Power Supply Frequency,

Pulse Width, Pulse Integration, and Velocity) Measurement

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 701210

Reviews:

YOKOGAWA 701210, User Manual, Page: 211 / 747

Search results

Summary of Contents for 701210

Reviews: