manualshive.com logo in svg

YOKOGAWA 701210, User Manual, Page: 129 / 747

Share
Download
YOKOGAWA 701210 User Manual Download Page 129

3-26

IM 701210-05E

When Using a Bridge Head with a MIL Standard (MIL-C-26482) Connector Wiring

The connector on the Strain Module (701270) is a NDIS connector

1

.  Use a connector

adapter cable (700935) by YOKOGAWA to make a MIL-NDIS conversion and connect to

the Strain Module (701270).

1. A connector recommended by JSNDI (The Japanese Society for Non-destructive Inspection)

Connector adapter cable
(700935)Length 1.5 m

Bridge head with a MIL 

standard connector wiring

A

B

C

D

E

F

G

A
B
C
D

C

NDIS

MIL

B
D
A

Pin arrangement of an NDIS connector

Pin arrangement of a MIL standard connector

Terminal

relationship

A

B

C

D

E

F

A: (positive bridge voltage)
B: Input- (negative measurement signal)
C: Bridge- (negative bridge voltage)
D: Input+ (positive measurement signal)
E: Floating common
F: Sense+
     (positive bridge voltage sensing)
G: Sense–
     (negative bridge voltage sensing)

A:
B:Signal–
C:Exc
D:Excitation–
E:NC (no connection)
F:NC (no connection)

Strain Module
701270 (STRAIN_NDIS)

When Using the A1002JC Connector by YOKOGAWA

You can create your own cable by using the YOKOGAWA A1002JC connector that is

compatible with the strain module and use the cable to connect a strain gauge bridge or

a strain gauge transducer to the strain module.

A

A: (positive bridge voltage)
B:Input- (negative measurement signal)
C:Bridge- (negative bridge voltage)
D:Input+ (positive measurement signal)
E:Floating common
F:Sense+ (positive bridge voltage sensing)
G:Sense- (positive bridge voltage sensing)

B

C

D

E

F

G

Pin arrangement

A1002JC NDIS connector
(2 pieces in one set)

(1)

When viewed along arrow (1)

Note

•

The connector shell is connected to the case potential (earth) of the DL750/DL750P.

•

Signals A through G are isolated inside the module.

•

When creating your own cable, we recommend that you use a shielded cable in order to
shut out external noise.

CAUTION

Take extra care when wiring the connectors.  If the wiring is shorted or incorrect,

it can damage the DL750/DL750P or other instruments that are connected to the

DL750/DL750P.

3.10 Connecting a Bridge Head (Only on Strain Modules)

Summary of Contents for 701210












































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments