Xerox DocuPrint 180 Message Manual Download Page 253

Page: 253 / 356

SUMMARY SHEET ERROR MESSAGES

XEROX DOCUPRINT 180 LPS MESSAGE GUIDE

14-11

Unexpected disk error <I/O error code: nB> creating temporary
file fileType>fileName.

An error was found while writing to the system disk. The system disk
has one or more bad sectors which are not in the bad block file.

Action

1. Resend the document.

2. If the problem continues, contact your systems specialist or

Xerox Customer Service.

Note:

In this message, the letter “B” indicates an octal value.

Unexpected error. Code = n.

An error occurred during processing.

Action

Contact your systems specialist or Xerox Customer Support.

Unknown state discovered during attempted MARK Recovery.

MARK Recovery failed.

Action

1. Take appropriate actions for the prior message(s).

2. Resend the job.

Virtual memory limit exceeded.

Dynamic memory was exhausted.

Action

None.

XDPS interface requested job termination.

The host has requested that the job be ended.

Action

Resend the job.

Summary of Contents for DocuPrint 180





































































































































































































































































































































































Search results

Summary of Contents for DocuPrint 180

Reviews:

Related manuals for DocuPrint 180

Brands by name

Popular brands

Xerox DocuPrint 180, Message Manual

Search results

Summary of Contents for DocuPrint 180

Reviews:

Related manuals for DocuPrint 180

Brands by name

Popular brands