Lenovo HX3510-G Installation And Service Manual Download Page 395

Page: 395 / 1240

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0509

User Response

No action; information only.

•

80030021-0782ffff : Sensor [SensorElementName] has deasserted. (PCIe Dev LK Down)

This message is for the use case when an implementation has detected a Sensor has deasserted.

May also be shown as 800300210782ffff or 0x800300210782ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0509

User Response

No action; information only.

•

80030108-1301ffff : Sensor [SensorElementName] has asserted. (PS Heavy Load)

This message is for the use case when an implementation has detected a Sensor has asserted.

May also be shown as 800301081301ffff or 0x800301081301ffff

Severity

Info

Serviceable

Appendix A. Integrated management module II (IMM2) error messages

383

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands