Lenovo HX3510-G Installation And Service Manual Download Page 807

Page: 807 / 1240

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0811

User Response

No action; information only.

•

810b050a-1e84ffff : Non-redundant:Insufficient Resources for [RedundancySetElementName]

has deasserted. (Fan Zone 4)

This message is for the use case when a Redundancy Set has transitioned from Non-redundant:Insufficient
Resources.

May also be shown as 810b050a1e84ffff or 0x810b050a1e84ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0811

User Response

No action; information only.

•

810b050c-2581ffff : Non-redundant:Insufficient Resources for [RedundancySetElementName]

has deasserted. (Backup Memory)

This message is for the use case when a Redundancy Set has transitioned from Non-redundant:Insufficient
Resources.

May also be shown as 810b050c2581ffff or 0x810b050c2581ffff

Appendix A. Integrated management module II (IMM2) error messages

795

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands