Lenovo HX3510-G Installation And Service Manual Download Page 669

Page: 669 / 1240

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0126

User Response

Make sure that DIMMs are installed in the correct sequence and have the same size, type, speed,
and technology.

•

806f070c-2006ffff : Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 6)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

May also be shown as 806f070c2006ffff or 0x806f070c2006ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0126

User Response

Make sure that DIMMs are installed in the correct sequence and have the same size, type, speed,
and technology.

•

806f070c-2007ffff : Configuration Error for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 7)

This message is for the use case when an implementation has detected a Memory DIMM configuration
error has been corrected.

May also be shown as 806f070c2007ffff or 0x806f070c2007ffff

Severity

Error

Serviceable

Yes

Appendix A. Integrated management module II (IMM2) error messages

657

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands