Lenovo HX3510-G Installation And Service Manual Download Page 1057

Page: 1057 / 1240

1. No action required. The system will reboot at the end of POST.

2. If the problem persists, switch to the backup UEFI image or update the current UEFI image.

Replace the system board.

•

W.305800D DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'.

DRIVER HEALTH PROTOCOL: Disconnect Controller Failed. Requires 'Reboot'

Explanation:

Severity

Warning

User Response

Complete the following steps:

1. No action required. The system will reboot at the end of POST.

2. If the problem persists, switch to the backup UEFI image or update the current UEFI image.

Replace the system board.

•

W.305800E DRIVER HEALTH PROTOCOL: Reports Invalid Health Status Driver. DRIVER HEALTH

PROTOCOL: Reports Invalid Health Status Driver

Explanation:

Severity

Warning

User Response

Complete the following steps:

1. No action required. The system will reboot at the end of POST.

2. If the problem persists, switch to the backup UEFI image or update the current UEFI image.

Replace the system board.

•

W.3808000 An IMM communication failure has occurred. IMM Communication Failure

Explanation:

Severity

Warning

User Response

Complete the following steps:

1. Reset the IMM from the CMM.

2. Use the CMM to remove auxiliary power from the compute node. This will reboot the compute

node.

3. Check the IBM support site for an applicable service bulletin or firmware update that applies to

this error.

Update the UEFI Firmware.

5. (Trained service technician only) Replace the system board.

Appendix B. UEFI/POST diagnostic codes

1045

«
...
1055
1056
1057
1058
1059
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands