Lenovo HX3510-G Installation And Service Manual Download Page 264

Page: 264 / 1240

CIM Information

Prefix:

IMM

ID:

0026

User Response

Information only; no action is required.

•

4000001b-00000000 : Management Controller [arg1]: Configuration restored from a file by user

[arg2].

This message is for the use case where a user restores a Management Controller configuration from a file.

May also be shown as 4000001b00000000 or 0x4000001b00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0027

User Response

Information only; no action is required.

•

4000001c-00000000 : Watchdog [arg1] Screen Capture Occurred.

This message is for the use case where an operating system error has occurred and the screen was
captured.

May also be shown as 4000001c00000000 or 0x4000001c00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - other

SNMP Trap ID

CIM Information

252

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands