Lenovo HX3510-G Installation And Service Manual Download Page 183

Page: 183 / 1240

Front USB / operator
information panel cable

Figure 112. Cable connection

11. Replace the fan cage assembly (see “Replacing the fan cage assembly” on page 136).

12. Replace the top cover (see “Replacing the top cover” on page 118).

13. Slide the server into the rack.

14. Reconnect the power cords and any cables that you removed.

15. Turn on the peripheral devices and the server.

For the left EIA assembly

1. Read the safety information that begins on “Safety” on page v and “Removing and replacing guidelines”

on page 101.

2. Turn off the server and peripheral devices, and disconnect the power cord and all external cables.

3. Remove the top cover (see “Removing the top cover” on page 116).

4. Remove the fan cage assembly (see “Removing the fan cage assembly” on page 135).

5. Route the cable into the slot.

EIA assembly

Figure 113. Cable routing

Chapter 5

Removing, and replacing components

171

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands