Lenovo HX3510-G Installation And Service Manual Download Page 301

Page: 301 / 1240

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0101

User Response

Information only; no action is required.

•

40000066-00000000 : User [arg1] password modified.

A user account was changed

May also be shown as 4000006600000000 or 0x4000006600000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0102

User Response

Information only; no action is required.

•

40000067-00000000 : User [arg1] role set to [arg2].

A user account role assigned

May also be shown as 4000006700000000 or 0x4000006700000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

Appendix A. Integrated management module II (IMM2) error messages

289

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands