Lenovo HX3510-G Installation And Service Manual Download Page 327

Page: 327 / 1240

Automatically notify support

Alert Category

System - Remote Login

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0155

User Response

Information only; no action is required.

•

4000009c-00000000 : Remote Login Successful. Login ID: [arg1] from [arg2] serial interface.

This message is for the use case where a user successfully logs in to a Management Controller.

May also be shown as 4000009c00000000 or 0x4000009c00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Remote Login

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0156

User Response

Information only; no action is required.

•

4000009d-00000000 : Login ID: [arg1] from [arg2] at IP address [arg3] has logged off.

This message is for the use case where a user has logged off of a Management Controller.

May also be shown as 4000009d00000000 or 0x4000009d00000000

Severity

Info

Serviceable

Automatically notify support

Appendix A. Integrated management module II (IMM2) error messages

315

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands