Lenovo HX3510-G Installation And Service Manual Download Page 139 | Manualshive

Page: 139 / 1240

background image

The following notes describe the type of hard disk drives that the server supports and other information
that you must consider when you install a hard disk drive. For a list of supported hard disk drives, see
http://www.lenovo.com/ serverproven/.

• Locate the documentation that comes with the hard disk drive and follow those instructions in addition to

the instructions in this chapter.

• Make sure that you have all the cables and other equipment that are specified in the documentation that

comes with the drive.

• Select the bay in which you want to install the drive.

• Check the instructions that come with the drive to determine whether you have to set any switches or

jumpers on the drive. If you are installing a SAS or SATA hard disk drive, be sure to set the SAS or
SATA ID for that device.

• The hot-swap server models support up to twenty-four 2.5-inch or eight 3.5-inch hot-swap SAS or

SATA hard disk drives.

• The electromagnetic interference (EMI) integrity and cooling of the server are protected by having all

bays and PCI Express slots covered or occupied. When you install a drive or a PCI Express adapter,
save the EMC shield and filler panel from the bay or PCI Express adapter slot cover in the event that
you later remove the device.

To install a hot-swap SAS or SATA hard disk drive, complete the following steps:

Note:

If you have only one hard disk drive, you must install it in the bay 0 (upper-left).

Step 1.

Read the safety information that begins on “Safety” on page v and “Removing and replacing
guidelines” on page 101.

Step 2.

Remove the filler panel from the empty drive bay. Keep the filler panel in a safe place.

Step 3.

Touch the static-protective package that contains the drive to any unpainted metal surface on the
server; then, remove the drive from the package and place it on a static-protective surface.

Step 4.

Install the hard disk drive in the drive bay:

a.

Make sure that the tray handle is in the open (unlocked) position.

b.

Align the drive with the guide rails in the bay.

00

00

00

00

00

00

00

00

00

00

00

00

000000

000000

000000

000000

000000

Latch

Handle

Filler panel handle

2.5-inch hot-swap
hard disk drive

Figure 56. 2.5-inch hot-swap hard disk drives installation

.

Removing, and replacing components

127

«
...
137
138
139
140
141
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX3510-G

BladeCenter HS23

Brand: IBM Pages: 30

System x3950 X6

Brand: IBM Pages: 53

8649 - Eserver xSeries 225

Brand: IBM Pages: 194

Brand: Vxl Pages: 2

Brand: Cabletron Systems Pages: 100

Sun Fire Netra 1280

Brand: Sun Microsystems Pages: 10

TVS- 72XU Series

Brand: QNAP Pages: 56

Brand: HP Pages: 94

Integrity rx5670

Brand: HP Pages: 46

Brand: HP Pages: 98

NetServer AA 4000

Brand: HP Pages: 82

Brand: HP Pages: 25

HPE ProLiant ML30 Gen9

Brand: HP Pages: 112

Brand: HP Pages: 28

Brand: HP Pages: 56

Hyper Converged 380

Brand: HP Pages: 125

Brand: HP Pages: 23

integrity rx2800 i4

Brand: HP Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands