Lenovo HX3510-G Installation And Service Manual Download Page 622 | Manualshive

Page: 622 / 1240

background image

Note: Each time you install or remove a DIMM, you must disconnect the server from the power
source; then, wait 10 seconds before restarting the server.

1. Refer to TIP H212293 for minimum code level.

2. Check the Lenovo support website for an applicable retain tip or firmware update that applies

to this memory error.

3. Swap the affected DIMMs (as indicated by the error LEDs on the system board or the event

logs) to a different memory channel or microprocessor.

4. If the error still occurs on the same DIMM, replace the affected DIMM.

5. (Trained technician only) If the problem occurs on the same DIMM connector, check the DIMM

connector. If the connector contains any foreign material or is damaged, replace the system
board.

6. (Trained technician only) Remove the affected microprocessor and check the microprocessor

socket pins for any damaged pins. If a damage is found, replace the system board.

7. (Trained technician only) Replace the affected microprocessor.

One of the DIMMs :

•

806f050d-0400ffff : Array [ComputerSystemElementName] is in critical condition. (Drive 0)

This message is for the use case when an implementation has detected that an Array is Critical.

May also be shown as 806f050d0400ffff or 0x806f050d0400ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

5

CIM Information

Prefix:

PLAT

ID:

0174

User Response

1. Make sure that the RAID adapter firmware and hard disk drive firmware are at the latest level.

2. Make sure that the SAS cable is connected correctly.

3.

Replace the SAS cable.

4. Check backplane cable connection.

5.

Replace the RAID adapter.

6. Replace the hard disk drive that is indicated by a lit status LED.

610

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
620
621
622
623
624
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for HX3510-G

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: Panasonic Pages: 16

SuperServer 5013C-MT

Brand: Supero Pages: 98

Brand: Axis Pages: 10

Transport GT26-B4987

Brand: TYAN Pages: 125

xPort Pro XPP1004000-02R

Brand: Lantronix Pages: 17

Brand: NEC Pages: 10

PRIMERGY RX100 S7

Brand: Fujitsu Pages: 86

PRIMERGY RX1330 M1

Brand: Fujitsu Pages: 312

Primergy RX100 S4

Brand: Fujitsu Pages: 85

PRIMERGY RX1330 M1

Brand: Fujitsu Pages: 84

Primergy RX100 S3

Brand: Fujitsu Pages: 73

PRIMERGY RX100 S8

Brand: Fujitsu Pages: 82

PRIMERGY RX1330 M3

Brand: Fujitsu Pages: 342

PRIMERGY RX100 S7

Brand: Fujitsu Pages: 490

PRIMERGY RX1330 M3

Brand: Fujitsu Pages: 84

Brand: D-Link Pages: 113

Brand: D-Link Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands