Lenovo HX3510-G Installation And Service Manual Download Page 1061

Page: 1061 / 1240

•

W.58007 Invalid memory configuration (Unsupported DIMM Population) detected. Please verify

memory configuration is valid. Unsupported DIMM Population

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Ensure that the DIMM connectors are populated according to the guidelines in the service

information for this product.

2. Ensure all DIMMs are enabled in the uEFI setup menu.

3. If a DIMM connector error LED is lit, resolve the failure.

•

W.580A1 Invalid memory configuration for Mirror Mode. Please correct memory configuration.

Unsupported DIMM Population for Mirror Mode

Explanation:

Severity

Error

User Response

Complete the following steps:

1. If a DIMM connector error LED is lit, resolve the failure.

2. Make sure that the DIMM connectors are correctly populated for mirroring mode.

•

W.580A2 Invalid memory configuration for Sparing Mode. Please correct memory configuration.

Unsupported DIMM Population for Spare Mode

Explanation:

Severity

Error

User Response

Complete the following steps:

1. If a DIMM connector error LED is lit, resolve the failure.

2. Make sure that the DIMM connectors are correctly populated for sparing mode, according to

the service information for this product.

•

W.68002 A CMOS battery error has been detected CMOS Battery Fault

Explanation:

Severity

Error

User Response

Complete the following steps:

Appendix B. UEFI/POST diagnostic codes

1049

«
...
1059
1060
1061
1062
1063
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands