Lenovo HX3510-G Installation And Service Manual Download Page 1010

Page: 1010 / 1240

This message is for the use case when an implementation has detected a Processor has been Enabled.

May also be shown as 816f08072584ffff or 0x816f08072584ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0060

User Response

No action; information only. One of the CPUs :

•

816f0813-2581ffff : System [ComputerSystemElementName] has recovered from an Uncorrectable

Bus Error. (DIMMs)

This message is for the use case when an implementation has detected a that a system has recovered
from a Bus Uncorrectable Error.

May also be shown as 816f08132581ffff or 0x816f08132581ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0241

User Response

No action; information only.

•

816f0813-2582ffff : System [ComputerSystemElementName] has recovered from an Uncorrectable

Bus Error. (PCIs)

998

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
1008
1009
1010
1011
1012
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands