Lenovo HX3510-G Installation And Service Manual Download Page 931

Page: 931 / 1240

•

816f0507-0301ffff : [ProcessorElementName] has Recovered from a Configuration Mismatch.

(CPU 1)

This message is for the use case when an implementation has Recovered from a Processor Configuration
Mismatch.

May also be shown as 816f05070301ffff or 0x816f05070301ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0063

User Response

No action; information only.

•

816f0507-0302ffff : [ProcessorElementName] has Recovered from a Configuration Mismatch.

(CPU 2)

This message is for the use case when an implementation has Recovered from a Processor Configuration
Mismatch.

May also be shown as 816f05070302ffff or 0x816f05070302ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0063

User Response

No action; information only.

Appendix A. Integrated management module II (IMM2) error messages

919

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands