Lenovo HX3510-G Installation And Service Manual Download Page 748

Page: 748 / 1240

•

81010204-1d05ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 5A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102041d05ffff or 0x810102041d05ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

User Response

No action; information only. Fan 5B Tach :

•

81010204-1d06ffff : Numeric sensor [NumericSensorElementName] going low (lower critical) has

deasserted. (Fan 6A Tach)

This message is for the use case when an implementation has detected a Lower Critical sensor going low
has deasserted.

May also be shown as 810102041d06ffff or 0x810102041d06ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Fan Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0481

User Response

No action; information only. Fan 6B Tach :

736

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands