Lenovo HX3510-G Installation And Service Manual Download Page 1102

Page: 1102 / 1240

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check the Ethernet cable for damage and ensure correct cable type and attachment.

2. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

3. Rerun the test.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA LSI hard drive test results

The following messages can result when you run the LSI hard drive test.

Test results for the DSA LSI hard drive test

The following messages can result when you run the DSA LSI hard drive test.

•

407-000-000 : LSIESG:DiskDefaultDiagnostic Test Passed

The test passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

407-800-000 : LSIESG:DiskDefaultDiagnostic Test Aborted

1090

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
1100
1101
1102
1103
1104
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands