Lenovo HX3510-G Installation And Service Manual Download Page 1216

Page: 1216 / 1240

•

264-905-000 : Tape Test Failed

Tape Test Failed. Software error: invalid request.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. If the system has stopped responding, turn off and restart the system.

2. Check the system firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

3. Run the test again.

4. If the system has stopped responding, turn off and restart the system.

5. Make sure that the drive firmware is at the latest level.

6. Run the test again.

7. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-906-000 : Tape Test Failed

Tape Test Failed. Unrecognized error.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

3. Make sure that the drive firmware is at the latest level.

1204

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

«
...
1214
1215
1216
1217
1218
...
»

Summary of Contents for HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands

Lenovo HX3510-G, Installation And Service Manual

Search results

Summary of Contents for HX3510-G

Reviews:

Related manuals for HX3510-G

Brands by name

Popular brands